Depending on your current or desired configuration the All Platform Configurations check box may need to be selected to display the option in the drop down menu.
The configuration page is used to change:
How the 65R interacts with the aircraft it is connected to.
The triggering method
In most cases the 65R is preconfigured based on what aircraft/system the camera is ordered for and the configuration doesn't need to be changed.
To learn how to change the configuration of the 65R or change the overlap for auto-height overlap mode, see the pages linked below.
The platform and metadata configuration is used to tell the 65R what aircraft it will be used with and where data sources (altitude, GPS, heading, etc) will come from.
The Config File field will display the currently config file. It also contains the change button used for changing the config file.
Depending on the current config file there will be limited config files displayed in the change menu. To display all configuration file options select the "All platform configurations" and/or the "Advanced configurations" radio buttons as shown in the advanced tab below.
The Config Type is tied to the config file and gives more specific instruction about the metadata sources. The config names and data source information are listed below.
DJI Skyport
DJI Autopilot
DJI Autopilot
DJI Autopilot
M300 M350 M200 M210
Sentera GPS
Sentera External GPS
65R Sensor Internal IMU
65R Sensor
M300 M350 M200 M210
Astro IF800 IF1200 Custom
Freefly Astro Gimbal
Astro Autopilot
Astro Autopilot
Astro Autopilot
Astro
IF800
IF800 Autopilot
IF800 Autopilot
IF800 Autopilot
IF800
IF1200A
IF200 Autopilot
IF200 Autopilot
IF200 Autopilot
IF1200
MAVLink-V2
MAVlink Autopilot
MAVlink Autopilot
MAVlink Autopilot
Custom MAVlink Autopilot Systems
Sentera PHX
PHX Autopilot (MAVlink V1)
PHX Autopilot (MAVlink V1)
PHX Autopilot (MAVlink V1)
PHX
DGR Dual Fixed - Primary
Sentera DGR Sensor Package
Sentera DGR Sensor Package
Sentera DGR Sensor Package
M300 M350
DGR Dual Fixed - Secondary
Sentera DGR Sensor Package
Sentera DGR Sensor Package
Sentera DGR Sensor Package
M300 M350
DGR Dual Gimbal - Primary
Sentera DGR Sensor Package
Sentera DGR Sensor Package
Sentera DGR Sensor Package
M300 M350
DGR Dual Gimbal - Secondary
Sentera DGR Sensor Package
Sentera DGR Sensor Package
Sentera DGR Sensor Package
M300 M350
DJI M300 DGR
Sentera DGR Sensor Package
Sentera DGR Sensor Package
Sentera DGR Sensor Package
M300 M350
Configurations with 65R Sensor Internal IMU as an Attitude source does not contain yaw/heading information and must be flown east facing.
The trigger field is used to set the trigger type and related settings.
The Command trigger type is used when the trigger commands come directly from the aircraft autopilot.
No settings are provided for this mode. The sensor will only trigger if it receives a trigger command from MAVLink, the web page, Payload SDK, or the custom Sentera Protocol.
The External trigger type is used when an external source is used to trigger the 65R.
There are 4 options for the external trigger commands. See the details in the table below.
Rising Edge
The trigger input must be stable for 50 milliseconds to register as a commanded trigger. This is also known as the mechanical switch debounce period.
Falling Edge
The trigger input must be stable for 50 milliseconds to register as a commanded trigger. This is also known as the mechanical switch debounce period.
Low PWM
The lower value of the PWM TRIGGER input in milliseconds.
High PWM
The higher value of the PWM TRIGGER input in milliseconds.
The trigger input is the TRIGGER signal on connector J2.
