65R image settings are set by default for the best settings in most use cases. There is also the ability to alter some of the color and exposure settings for custom applications.
Changing these values is not necessary for most applications and may prevent standard analytics from being run.
In most normal usage, the exposure should not need to be adjusted, however if your images are consistently too bright or too dark, the auto-exposure settings can be modified. These settings will change how bright / dark the image is, as well as the shutter speeds and gains used to capture the image.
0 - 255
60
Sets the average pixel value across the entire frame that the auto-exposure attempts to achieve. It is the highest 8 bits of any imager, and is calculated before any ISP corrections are performed. This means that the final image will likely have an average brightness much higher than this target due to vignetting and gamma correction being applied in later steps. Due to this, in general the target value should be kept lower than 100.
200 - {Shutter Max}
400
This value is the shortest shutter speed in us (microseconds) that will be used before the camera drops to a lower ISO. If the camera is already running at the lowest ISO, then the shutter speed will go faster until it hits the limit of the sensor.
{Shutter Min} – 25000
2000
This value is the longest shutter speed in us (microseconds) the camera will use before increasing the ISO to attempt to stay below this value. For most flights, you should not see a longer shutter speed unless the field has insufficient lighting, forcing the shutter to go longer (see Shutter Unlock). It is recommended to keep this value lower than 3ms (3000us) to avoid motion blur caused by the groundspeed of the UAV.
100 – 12800
600
If the ISO gets set to this value or greater by the auto-exposure, then the shutter max value is ignored, allowing the shutter speed to go slower. This is to prevent the camera from using very high gains, which can have worse effects on image quality than the motion blur from a slow shutter speed . It is also useful for taking images indoors, where lighting is insufficient to capture images otherwise.
These settings allow adjustment to the overall brightness, contrast, and saturation of the image without modifying the exposure. They should be used for fine color adjustment if the default settings are not giving the quality of image needed for your application.
0.0 – 2.0
1.0
Adjusts the difference between the light and dark values. This effectively multiplies every value by X. So setting this to 1.1 will take 1.1x each pixel value. For example, if you have a value of 20 and 200 (180 apart) normally, setting contrast to 1.1 will change the values to 22 and 220 (198 apart) effectively increasing the contrast between bright and dark.
0.0 – 2.0
1.0
Adjusts the vibrancy of the color in the image. This will affect the color and changing this by too much can result in imagery with less ‘true’ color. This increases the ‘contrast’ of each color. For example, if something is bright green, increasing saturation adjusts it to be even more green than a darker green in the same image.
There are several onboard processing steps that the sensor performs to provide the best data product possible. While we recommend leaving these at their default settings, each of the processing stages can be disabled to get completely unmodified imagery from the sensor.
Enabled
This enables use of the internal color correction matrix on the sensor. The purpose is to compensate for the exact response of the sensor and produce an image with correct color and white balance. Disabling this is not recommended, as the resulting images will appear ‘greenish’ due to the sensitivity profile of the imager.
The settings on this page can be applied while a session is currently running and no reboot of the camera is needed.
After modifying one or more values, click the ‘Apply’ button in the lower right corner of the page. The settings will be updated for the next trigger.
If a session is currently running, the ‘Capture Image’ button will be enabled on this page to allow more rapid testing of settings changes. Sessions can be started from the `Home` page if one isn’t currently running.
Large changes to auto-exposure will apply right away, but the camera may take 10+ seconds to stabilize on the new exposure settings. Other settings changes are reflected in the images much quicker.
