# How To Access Web User Interface

## Power Sensor

Power the sensor using the AC power adapter or install into the aircraft and turn the aircraft on. 

Then wait for the LEDS on the sensor to do the following:

| Power Method     | LED Behavior                                                                  |
| ---------------- | ----------------------------------------------------------------------------- |
| AC Power Adapter | Flashings Red                                                                 |
| Drone Power      | <p>Solid Green (Requires GPS Fix)<br>Solid Red ( After 2 minutes w/o GPS)</p> |

This verifies that the sensor is fully booted.

<figure><img src="https://3675182560-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FXxc0lOfDa92aCfFa5lb4%2Fuploads%2FXtqGetUrOGYhAIDg8pkM%2Fimage.png?alt=media&#x26;token=f23f7090-a619-43ca-a782-1fbf3647e700" alt=""><figcaption></figcaption></figure>

## Connect To Computer

Connect the sensor to the computer using a USB cable.&#x20;

{% hint style="info" %}
Use the USB-C port on the sensor not the USB-C port on the top of the gimbal.&#x20;
{% endhint %}

<figure><img src="https://3675182560-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FXxc0lOfDa92aCfFa5lb4%2Fuploads%2FRbDJ6SjMypg5a8A6EuLy%2Fimage.png?alt=media&#x26;token=9f7efe02-a11f-4048-b8d8-c94e6f97cac3" alt=""><figcaption></figcaption></figure>

## Verify Connection

Open your wifi/network panel from the task bar. Verify that you see "unidentified network - No internet". This is the 65R appearing as a network device.

<figure><img src="https://3675182560-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FXxc0lOfDa92aCfFa5lb4%2Fuploads%2FLNWPwCOexuorbGGoNyTq%2Fimage.png?alt=media&#x26;token=0211a02e-f8fa-46cf-b802-608b6a960d73" alt="" width="302"><figcaption></figcaption></figure>

## Open Web Browser

Open a web browser (chrome, safari, firefox, etc).&#x20;

{% hint style="info" %}
No internet connection is required.&#x20;
{% endhint %}

<figure><img src="https://3675182560-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FXxc0lOfDa92aCfFa5lb4%2Fuploads%2F3lF7LgN2pKtHqFIzAmQW%2Fimage.png?alt=media&#x26;token=e1140930-e396-4f58-b0d1-1c53b24ce957" alt=""><figcaption></figcaption></figure>

## Enter IP Address

In the address bar enter 192.168.42.1 and press enter/go.&#x20;

<figure><img src="https://3675182560-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FXxc0lOfDa92aCfFa5lb4%2Fuploads%2FwX4qFdaklrDbmPsKyrrz%2Fimage.png?alt=media&#x26;token=0d3ee7ec-2f5a-4f7d-b159-dcb69e2c0258" alt=""><figcaption></figcaption></figure>

## Page Appears

The webpage will appear.&#x20;

<figure><img src="https://3675182560-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FXxc0lOfDa92aCfFa5lb4%2Fuploads%2FWOMPyluEw969C2aSTA82%2F65r%20homepage.png?alt=media&#x26;token=47a4f071-d1df-4471-a87b-0621057642f9" alt=""><figcaption></figcaption></figure>

{% hint style="info" %}
If the webpage can't be connected to after a few minutes try the following:\
\- Verify the sensor has had around a minute to boot. \
\- Turn off/disconnect any Wi-Fi or Ethernet connections that have internet access.\
\- Verify the USB cable being used is the provided cable or one of the listed compatible cables.
{% endhint %}

{% hint style="info" %}
If the 65R is being powered with the AC power adapter, the No Gimbal Communication application will appear. This is expected as the gimbal itself is now powered.&#x20;
{% endhint %}

<figure><img src="https://3675182560-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FXxc0lOfDa92aCfFa5lb4%2Fuploads%2FGaJWsXIYOieXK5a6cFmI%2F65R%20home%20AC.png?alt=media&#x26;token=4342ea51-136f-4edd-9063-09a7aee31893" alt=""><figcaption></figcaption></figure>