For the complete documentation index, see llms.txt. Markdown versions of documentation pages are available by appending .md to page URLs.
Skip to content

Colorization and visualization

Change how a layer is colored to see the variation across a field. Colorization works the same way on drone mosaics, satellite scenes and analytics. The settings below apply to any index or analytic layer.


Set a layer's colors

Open the layer's details and scroll to Colorization. A multispectral mosaic shown as a composite has no colors to set, so choose an index such as NDVI first.

Home Field's Multispectral Mosaic as NDVI with the Colorization module outlined: 5 bins, the histogram, the range -1.00 to 1.00, By Area, the red-to-green Color Scale and Include Out-of-Range Values
Colorization highlighted

These are the settings you'll use most.

  • Drag the bins slider to split the values into 1 to 20 colors. Fewer bins show the broad pattern, and more bins show detail.

  • Drag the range handles to set the lowest and highest values that get a color. Values outside the range aren't drawn. To color them too, turn on Include Out-of-Range Values, and they take the lowest or highest color.

  • Choose By Area to give each color the same share of the field, which suits finding the best and worst parts of one layer. Choose By Range for equal value steps, so the same value always gets the same color. Use it to compare dates or fields.

  • Open Color Scale to choose another color ramp. The default runs from red (low) through yellow to green (high).

By Area colors are relative to the layer. With the default color scale, its lowest bin is red even when the whole field is healthy. When you want each color to mean a fixed value, use By Range.

Click Show More to open the color table. It lists each bin's color, values and area. Use it to put a number on what you see, such as how many acres of the field fall in the lowest NDVI bin.

The color table under Show Less: five bins with their colors, values from -1.00 to 0.57 up to 0.86 to 1.00, and 23.73 ac each

With Include Out-of-Range Values on, the lowest and highest bins also color the values outside the range. Their Area still counts only the part inside it.

All Colorization controls
Control
Description

Bins slider

Sets how many colors the values are divided into, from 1 to 20. Fewer bins make a simpler map that shows the broad pattern. More bins show more detail.

Histogram

Shows how the layer's values are distributed. Each bar takes the color of the bin it falls in, so you can see where the breaks are.

Range sliders

Set the lowest and highest values that are colored. Values outside the range aren't drawn unless Include Out-of-Range Values is on. The boxes under the slider show the current limits.

By Area

Sets the bin breaks so that each color covers the same area of the field. Good for seeing the best and worst parts of one layer.

By Range

Sets the bin breaks at equal value intervals. Good for comparing layers from different dates or different fields, because the same value always gets the same color.

Custom

Lets you set the break values yourself.

Color Scale

Chooses the color ramp from a menu of gradient swatches. The default runs from red (low) through yellow to green (high).

Include Out-of-Range Values

When on, values below the range take the lowest color and values above it take the highest, so the whole layer stays visible.

Show More

Expands the color table. For each bin it lists its Color, the range of Values it covers and the Area of the field in that bin. Show Less folds it away again.

The other color scales are brown to green, an elevation ramp, white to red and red through yellow to blue. There are also white to green, black to white, black to yellow and dark purple to yellow. Some layers open on a different default. A Canopy Cover layer opens on white to green, and the thermal band on dark purple to yellow.

Try it in the demo

In the demo below, a multispectral mosaic shown as NDVI is on the map with its details open. Try fewer bins, a narrower range, By Range, another color scale and the color table.

Open this demo full size


Settings for common jobs

Goal
Colorization settings

Find the weakest part of the field

1 bin. Drag the upper range handle down until only the low values are colored, then read the Area in the color table.

Find the strongest part of the field

1 bin. Drag the lower range handle up.

Compare two flights of the same field

The same index on both layers, with By Range and the same bins and range.

Split the field into three management classes

Switch Display Mode to Zone Rx (Beta). 3 bins with By Area or Custom breaks.


Choose what a multispectral mosaic shows

A Multispectral Mosaic stores every band the sensor captured, so one layer can show the crop as a picture, as an index or as a single band.

Open the mosaic's details and choose an option from the Visualization menu in Mosaic Details. The layer keeps the visualization you choose while it's on the map.

The Mosaic Details panel of a Multispectral Mosaic with the Visualization menu open, grouped into COMPOSITES with Color Infrared (NIR, R, G) selected and Natural Color (R, G, B) grayed out, INDICES with NDVI, NDRE, GNDVI, CIRE, CIG, NDWI and GLI, and BANDS with Green (560 nm), Red (650 nm), Red Edge (730 nm) and NIR (860 nm); the map shows the color infrared mosaic

Anything the survey's sensor can't produce is grayed out.

The same Multispectral Mosaic shown as NDVI, with the Colorization panel: a 5 bins slider, a histogram colored red to green, range values -1.00 and 1.00, By Area selected, a red-to-green Color Scale, the Include Out-of-Range Values toggle button off, Show More, and the Display Mode module below
The same mosaic with the NDVI visualization. Colorization and Display Mode appear in the panel.

Satellite indices and analytics such as a stand count have no Visualization menu. Sample-based analytics have a Display Property menu instead, which chooses the value shown on the dots. Their colorization works the same way.

Composites, indices and bands

Group
Options
Description

COMPOSITES

Color Infrared (NIR, R, G) and Natural Color (R, G, B)

A picture of the crop. There's no single value per pixel, so there are no colors to set.

INDICES

NDVI, NDRE, GNDVI, CIRE, CIG, NDWI and GLI

One value per pixel, so the panel adds Colorization, Display Mode and Zone Statistics.

BANDS

One entry per band the sensor captured, with its wavelength

The raw reflectance or temperature of one band. One value per pixel, so the panel adds Colorization, Display Mode and Zone Statistics.

The demo field under a Multispectral Mosaic shown as a composite
A composite: a picture of the crop, nothing to colorize.
The demo field under a VARI index layer colorized red to green
A VARI index: one value per pixel, colorized red to green.
The band list by sensor
Sensor
BANDS

DJI Mavic 3 Multispectral

Green (560 nm), Red (650 nm), Red Edge (730 nm), NIR (860 nm)

Sentera 6X Multispectral

Blue (475 nm), Green (550 nm), Red (670 nm), Red Edge (715 nm), NIR (840 nm)

Sentera 6X Thermal Pro

Green (550 nm), Red (670 nm), Red Edge (715 nm), NIR (840 nm), LWIR (11.00 μm)

Try it in the demo

In the demo below, switch one mosaic from a composite to two indices and a single band, and watch the panel change.

Open this demo full size


Thermal band

On a Sentera 6X Thermal Pro survey, open the Visualization menu and choose the thermal band, LWIR (11.00 μm), to map surface temperature. It opens on a dark-purple-to-yellow color scale, with values in Celsius to one decimal.

A Multispectral Mosaic from a 6X Thermal Pro survey shown as LWIR (11.00 μm): the research plots in dark purple, magenta and orange over the satellite basemap, and the Mosaic Details panel with Visualization LWIR (11.00 μm), a Colorization histogram in the same colors, the range 23.9 to 49.9, By Area, a dark purple to orange Color Scale, and the Display Mode selector

Map layersZones and zone statisticsZone Rx prescriptions

Last updated

Was this helpful?