For the complete documentation index, see llms.txt. This page is also available as Markdown.

Zones and zone statistics

Zones turn what you see on the map into numbers you can compare. Draw a zone around a hybrid strip, a treatment block or a wet spot, and every layer reports its values inside it.


Draw a zone

1

Start a zone

Open the field and click the plus icon add icon in the Zones module.

The Zones module with its plus icon
2

Name it

Type a Zone Name. The Date defaults to today.

The new zone form with Zone Name Hybrid comparison zone A, Date 10-11-2026 and the DONE button
3

Draw the shape

Draw the shape with the tool you need.

  • draw rectangle icon Draw Rectangle. Click two opposite corners.

  • draw polygon icon Draw Polygon. Click each corner and finish on the first point.

  • draw circle icon Draw Circle. Click the center and then the edge.

The new zone form with Zone Name set to Hybrid comparison zone A, a Date field, and a DONE button; on the map a white rectangle zone drawn inside the cyan field boundary, and the drawing toolbar on the right with Draw Rectangle active

The tool stays selected, so drawing again adds a second shape to the same zone. The other tools on the toolbar adjust the shape the same way as when you draw a field boundary.

The drawing toolbar at the right edge of the map
4

Save

Click DONE. The button is grayed out until the zone has a name and at least one shape.

DONE button

The zone appears in the Zones module under the field boundary, switched on. It also appears under Zone Statistics in a layer's details.

East Field with Hybrid comparison zone A, 18.08 ac, outlined in the Zones module under Field Boundary, and the zone drawn as a white rectangle on the map
Hybrid comparison zone A highlighted
lightbulb

Hand-drawn zones are for comparison. For rate zones split from a layer's values, use Zone Rx prescriptions instead.

Try it in the demo

In the demo below, name a zone, draw it as a rectangle and save it.

spinner

Open this demo full size


Show or hide zones on the map

When you open a field, only the field boundary is on the map. Choose the zones you want to see in the Zones picker.

1

Open the Zones picker

Click the layers icon layers icon in the Zones module.

2

Choose the zones

Click the circle next to a zone to draw it on the map. Click it again to take it off.

The Zones picker listing Field Boundary 15.63 ac and Zone 1 1.78 ac with green checks, Zone 2 0.43 ac and Zone 3 0.50 ac unselected, and the footer Total selected area: 17.41 ac; the selected zone is outlined on the map
3

Check the Zones module

The Zones module lists the field boundary and each zone on the map, along with its area. Hover over a row and click the × to take that zone, or the boundary, off the map. Click a zone to edit it, or click Field Boundary to edit the field's boundary.

East Field's Zones module outlined, listing Field Boundary 68.12 ac and Hybrid comparison zone A 18.08 ac, with the pointer over the zone's row showing its × icon
Zones module highlighted

Taking a zone off the map doesn't delete it. It stays in the picker, and its statistics still appear under Zone Statistics.


Rename, reshape or delete a zone

Click a zone's name in the Zones module to open Edit Zone. Change the name or use the draw tools to reshape the zone, then click DONE.

The Edit Zone panel with Zone Name set to Zone 1, a Date field, a blue DONE button and a red DELETE button; on the map the zone shows red vertex points, and the drawing toolbar on the right lists Draw Rectangle, Draw Polygon, Draw Circle, Move, Rotate, Edit, Cut, and Erase

To delete the zone, click DELETE and confirm in the Delete shape? box. A zone you delete is gone for good.

The Edit Zone panel with the Delete shape? confirmation box below DONE, reading This will be permanently deleted. above red DELETE and outlined CANCEL buttons; on the map the reshaped zone shows red corner points inside the field boundary
Edit Zone controls
Control
Description

Zone Name

The name shown in the Zones module and under Zone Statistics on every layer. Required.

Date

The date the zone belongs to.

edit icon Edit

Drags the red points. Click an edge to add a point there.

move icon Move and rotate icon Rotate

Shift or turn the whole shape.

cut icon Cut and erase icon Erase

Take area away from the shape.

Draw tools

Add a shape to the zone.

DONE

Saves the name, date and shape.

DELETE

Asks you to confirm in a Delete shape? box, then deletes the zone permanently. CANCEL keeps it.

Try it in the demo

In the demo below, rename a zone, drag one of its red points and delete another zone.

spinner

Open this demo full size


Read zone statistics

A layer's details page lists the values for each zone and the whole field.

1

Open the layer details

Turn on the layer you want to see numbers for. Click its name in the Map Layers module to open its details.

2

Find Zone Statistics

Scroll to Zone Statistics. The Field Boundary row gives the value for the whole field, and each zone below it gives the value inside that zone.

3

Find a zone on the map

Hover over a row to outline its zone on the map.

The Zone Statistics section of an NDVI layer listing Field Boundary 15.63 ac with 0.52 Average, Zone 1 1.78 ac with 0.82 Average, Zone 2 0.43 ac with 0.82 Average, and Zone 3 0.50 ac with 0.76 Average; the pointer is over Zone 1 and that zone is outlined in white on the NDVI map
Zone Statistics on an NDVI layer. The hovered zone is outlined in white on the map.

Each zone's statistics depend on the layer.

  • Stand counts and tassel counts show the minimum, average and maximum of the samples inside the zone.

  • Index layers, such as an NDVI mosaic or a satellite scene, show the zone's average value.

The Tassel Count layer details with the Zone Statistics section listing Field Boundary, Hybrid comparison zone A, and Hybrid comparison zone B, each with its area and Minimum, Average, and Maximum tassels per acre, above the Download Files section
Zone Statistics on a Tassel Count layer comparing two hybrid zones. Zones not shown on the map.
lightbulb

Zone statistics work across dates. Open a satellite NDVI layer from each week of the season and compare the field-boundary averages to follow the crop's dry-down.

Try it in the demo

In the demo below, open an NDVI layer's details, read its zone statistics and hover over a row to find its zone.

spinner

Open this demo full size


Download zones and zone statistics

Download a layer's zone statistics, such as the average NDVI or the stand count per zone, to work with them in a spreadsheet or GIS. The zones also download on their own, as shapes for other software.

Menu
Options
Description

more icon on the Zones module in the field view

Download as GeoJSON, Download as Shapefile, Download as CSV, Download as KML

The field boundary and the zones as shapes, for use in other software.

more icon next to Zone Statistics in a layer's details

Download as GeoJSON, Download as Shapefile, Download as CSV

The same shapes with that layer's statistics attached to each of them.

The Zone Statistics menu of an NDVI layer open, listing Download as GeoJSON, Download as Shapefile, and Download as CSV

Map layersColorization and visualizationDownload and export data

Last updated

Was this helpful?